More Topics on the right side of this page, also more pages on the topics at the bottom of this page!
 |
A Simple Way To Make Your Parts Look Good Posted by: TheToolandDieGuy
Video duration: 275 seconds |
![The Tool And Die Guy\](http://i.ytimg.com/vi/ZBrbdFC7OUI/2.jpg "The Tool And Die Guy\") |
The Tool And Die Guy's Mailbag: May 7, 2013 Posted by: TheToolandDieGuy
Video duration: 666 seconds |
 |
What a Hard Gauge is And How It Works Posted by: TheToolandDieGuy
Video duration: 221 seconds For more, visit: http://www.thetoolan ddieguy.com |
 |
Absolute Zero vs. Incremental Zero Explained Posted by: TheToolandDieGuy
Video duration: 377 seconds For more, visit http://www.thetoolan ddieguy.com |
 |
Building Confidence: The Tale of The Tags Posted by: TheToolandDieGuy
Video duration: 268 seconds For more, visit http://www.thetoolan ddieguy.com |
![The Tool and Die Guy\](http://i.ytimg.com/vi/1eVOhLSfkg4/2.jpg "The Tool and Die Guy\") |
The Tool and Die Guy's Mailbag, Edition 2 Posted by: TheToolandDieGuy
Video duration: 201 seconds For more, visit http://www.thetoolan ddieguy.com |
![The Tool and Die Guy\](http://i.ytimg.com/vi/Xd3D1YproOw/2.jpg "The Tool and Die Guy\") |
The Tool and Die Guy's Mailbag Posted by: TheToolandDieGuy
Video duration: 597 seconds http://www.thetoolan ddieguy.com |
 |
Angles Made Easy, Part 6 Posted by: TheToolandDieGuy
Video duration: 188 seconds For the rest of this series, please visit http://www.thetoolan ddieguy.com |
 |
A Brief Lesson On Countersinks Posted by: TheToolandDieGuy
Video duration: 242 seconds Most of us look at countersinks as a deburring tool. I used to do the same thing. In the Tool Room, that's what countersinks are usually used for. But there are a few variations that you need to know about. This informal video explains the basics of countersinks. |
 |
The Slide Hammer Posted by: TheToolandDieGuy
Video duration: 312 seconds |
![What\](http://i.ytimg.com/vi/atxt0rE-L4U/2.jpg "What\") |
What's This Hammer Used For? Posted by: TheToolandDieGuy
Video duration: 229 seconds For More, visit http://www.thetoolan ddieguy.com |
 |
The Ultimate Work Holding Device Posted by: TheToolandDieGuy
Video duration: 165 seconds |
 |
What To Do When Your Parts Get Magnetized Posted by: TheToolandDieGuy
Video duration: 182 seconds For more, visit http://www.thetoolan ddieguy.com |
 |
How Not To Drill Big Holes in Your Wrist Posted by: TheToolandDieGuy
Video duration: 94 seconds For more, visit http://www.thetoolan ddieguy.com |
 |
How To Drive Dowel Pins in Straight Every Time Posted by: TheToolandDieGuy
Video duration: 122 seconds For more, visit http://www.thetoolan ddieguy.com |
 |
How To Tell Your Boss or Customer You Made a Mistake Posted by: TheToolandDieGuy
Video duration: 411 seconds |
 |
Checking a Block For Squareness, Part II Posted by: TheToolandDieGuy
Video duration: 396 seconds |
 |
A Message From The Tool and Die Guy Posted by: TheToolandDieGuy
Video duration: 80 seconds Visit http://www.thetoolan ddieguy.com for more! |
 |
Are Metalworking/Tool & Die Trades For You? Posted by: TheToolandDieGuy
Video duration: 314 seconds |
 |
What Is The Difference Between a Mold and a Die? Posted by: TheToolandDieGuy
Video duration: 406 seconds For more visit http://www.thetoolan ddieguy.com |
 |
Fixturing 101: An Intro To Fixtures Posted by: TheToolandDieGuy
Video duration: 78 seconds |
 |
Sine Bars: Set-Up and How To Use Posted by: TheToolandDieGuy
Video duration: 229 seconds For more visit http://www.thetoolan ddieguy.com |
 |
Using a Hand Drill as An Cylindrical Grinder! Posted by: TheToolandDieGuy
Video duration: 207 seconds Am I a hack? You bet, when I can get away with it! |
 |
How To Get 2 Holes Lined Up Straight and Fast Posted by: TheToolandDieGuy
Video duration: 362 seconds For more, visit http://www.thetoolan ddieguy.com |
 |
How To Use Gauge Blocks and Dial Indicators Posted by: TheToolandDieGuy
Video duration: 583 seconds |
